Key Features:

• May be used as a pre-grouting sealer
• Allows moisture vapor transmission
• The NEW Rapid Cure formula protects in less than 4 hours
• Designed to achieve optimal penetration into dense, low-porosity surfaces

Suitable Tile Types

As a sealer or grout release for all natural stone surfaces, unglazed tile, porcelain, clay pavers, concrete, brick, masonry, and grout. For interior and exterior use.

General Surface Prep

Surface should be dry, clean and free of waxes, sealers or finishes. New installations need to be dry 48 hours before application. Protect painted surfaces. Test product in obscure area to ensure desirable results.

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN.
Wear skin and eye protection. Contains glycol ether monobutyl ether. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting. Seek medical attention. DO NOT
SPRAY.

Limitations to the Product

Do not allow sealer to come in contact with any non-recommended surface
May slightly lighten or darken some surfaces Sealer will not prevent surface wear or etching from acids or caustic Chemicals

Pre-Grout Sealer/Grout Release

Porous tile, such as clay and Saltillo pavers, can be stained by grout during installation. Sealing the tile before grouting will make grout removal much easier. Apply two coats of sealer according to directions after tile has been bonded for a minimum of 24 hours, or apply to front face of tile before installation.

Application of Product

USE CHECMICAL RESISTANT GLOVES SUCH AS NITRILE, WHILE HANDLING PRODUCT

Read entire label before using. Apply liberally using a new mop, paint pad applicator, sponge or brush. Allow it to penetrate for up to 5 minutes. Wipe surface completely dry using clean, dry cotton or paper towels after each application. Porous surfaces may require additional applications. Conduct a test to see if surface is completely sealed after 2 hours by applying drops of water on the surface. If it penetrates, apply an additional coat. If a residue is visible on the surface after drying, remove it with water and a white nylon scrub pad 60 minutes after application.

Drying Time

• Allow 30 minutes drying time between coats.
• Ready for surface traffic in 2 hours.
• Keep dry for 12 hours.
• Achieves a full cure in 24 hours.

Cleaning of equipment

Clean tools and hands with soap and water immediately after use.

Handling & Storage

• Close container tightly after each use store in original container only
• Store and use between temperatures of 40° F 90° F (4° C 32° C)

Product Maintenance

Do not use cleaners containing ammonia, acids or bleach. Use an appropriate TileLab® or Aqua Mix® neutral cleaner. Tile industry experts recommend periodic testing of sealed surfaces. Apply a few drops of water on the surface. If it soaks in, a coat of TileLab® or Aqua Mix® sealer will be necessary to keep sealer at peak performance.

Expected Wear

EXPECTED WEAR UP TO 15 YEARS

Will vary depending on hardness and texture of surface, type of area, surface wear, frequency, and type of maintenance products used Weather conditions, harsh cleaning methods, and high-alkaline, acidic, or solvent-based cleaners will affect wear

Suitable Tile Types

As a sealer or grout release for all natural stone surfaces, unglazed tile, porcelain, clay pavers, concrete, brick, masonry, and grout. For interior and exterior use.

General Surface Prep

Surface should be dry, clean and free of waxes, sealers or finishes. New installations need to dry 48 hours before application. Protect painted surfaces. Test product in obscure area to ensure desirable results.

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN.
Wear skin and eye protection. Do not breathe vapor or spray. Contains potassium methyl siliconate. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If respiratory tract is irritated, remove to fresh air. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting. Seek medical attention

Limitations to the Product

Do not allow product to come in contact with any non-recommended surface
May slightly lighten or darken some stone surfaces
Sealer will not prevent surface wear or etching from acids or caustic Chemicals

Pre-Grout Sealer/Grout Release

Porous tile, such as clay and Saltillo pavers, can be stained by grout during installation. Sealing the tile before grouting will make grout removal much easier. Apply two coats of sealer according to directions after tile has been bonded for a minimum of 24 hours, or apply to front face of tile before installation.

Application of Product

Read entire label before using. Apply liberally using a new mop, paint pad applicator, sponge or brush. Allow it to penetrate for up to 5 minutes. Wipe surface completely dry using clean, dry cotton or paper towels after each application. Porous surfaces may require additional applications. Conduct a test to see if surface is completely sealed after 2 hours by applying drops of water on the surface. If it penetrates, apply an additional coat. If a residue is visible on the surface after drying, remove it with water and a white nylon scrub pad 60 minutes
after application.

Drying Time

Allow 30 minutes drying time between coats.
Ready for surface traffic in 2 hours.
Keep dry for 12 hours.
Achieves a full cure in 24 hours.

Cleaning of equipment

Clean tools and hands with soap and water immediately after use.

Handling & Storage

Close container after each use
Store in original container only
Store and use between temperatures of 40° F 90°F (4° C 32°C)
Dispose of residue or any unused leftover product in accordance with
applicable federal, state, and local regulations

Product Maintenance

Do not use cleaners containing ammonia, acids or bleach. Use an appropriate TileLab® or Aqua Mix® neutral cleaner. Tile industry experts recommend periodic testing of sealed surfaces. Apply a few drops of water on the surface. If it soaks in, a coat of TileLab® or Aqua Mix® sealer will be necessary to keep sealer at peak performance.

Expected Wear

EXPECTED WEAR UP TO 10 YEARS
Will vary depending on hardness and texture of surface, type of area, surface wear, frequency, and type of maintenance products used Weather conditions, harsh cleaning methods, and high-alkaline, acidic, or solvent-based cleaners will affect wear

Key Features:

• Excellent Stain Protection
• No Sheen, Natural Look
• Safe, Water – Based Formula

Environment Consideration

Complies with all Federal EPA and SCAQMD standards for VOC

Suitable Tile Types

As a sealer or grout release for all natural stone surfaces, unglazed tile, porcelain, clay pavers, concrete, brick, masonry, and grout. For interior and exterior use.

General Surface Prep

Surface should be dry, clean and free of waxes, sealers or finishes. New installations need to dry 48 hours before application. Protect painted surfaces. Test product in obscure area to ensure desirable results.

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN.
Wear skin and eye protection. Do not breathe vapor or spray. Contains potassium methyl siliconate. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If respiratory tract is irritated, remove to fresh air. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting. Seek medical attention.

Limitations to the Product

Do not allow product to come in contact with any non-recommended surface If product is allowed to dry on surface, a white film may form. If this occurs, scrub surface with water and a white nylon pad Sealer will not prevent surface wear or etching from acids or caustic chemicals Note: Aqua Mix® UltraSolv® or Sealer’s Choice® Gold Rapid Cure Formula are recommended in place of Penetrating Sealer in food preparation areas or where maximum stain protection is required Pre-Grout Sealer/Grout Release Porous tile, such as clay and Saltillo pavers, can be stained by grout during installation. Sealing the tile before grouting will make grout removal much easier. Apply two coats of sealer according to directions after tile has been bonded for a minimum of 24 hours, or apply to front face of tile before installation

Application of Product

USE CHEMICAL RESISTANT GLOVES, such as nitrile, when handling product
Read entire label before using. Apply liberally using a new mop, paint pad applicator, sponge or brush. Allow it to penetrate for up to 5 minutes. Wipe surface completely dry using clean, dry cotton or paper towels after each application. Porous surfaces may require additional applications. Conduct a test to see if surface is completely sealed after 2 hours by applying drops of water on the surface. If it penetrates, apply an additional coat. If a residue is visible on the surface after drying, remove it with water and a white nylon scrub pad 60 minutes after application.

Drying Time

• Allow 30 minutes drying time between coats.
• Ready for surface traffic in 2 hours.
• Keep dry for 12 hours.
• Achieves a full cure in 24 hours.

Cleaning of equipment

Clean tools and hands with soap and water immediately after use.

Handling & Storage

• Close container tightly after each use
• Store in original container only
• Store and use between temperatures of 40° F 90° F (4° C 32° C)

Product Maintenance

Do not use cleaners containing ammonia, acids or bleach. Use an appropriate TileLab® or Aqua Mix® neutral cleaner. Tile industry experts recommend periodic testing of sealed surfaces. Apply a few drops of water on the surface. If it soaks in, a coat of TileLab® or Aqua Mix® sealer will be necessary to keep sealer at peak performance.

Expected Wear

EXPECTED WEAR UP TO 5 YEARS

Will vary depending on hardness and texture of surface, type of area, surface wear, frequency, and type of maintenance products used Weather conditions, harsh cleaning methods, and high-alkaline, acidic, or solvent-based cleaners will affect wear

General Surface Prep

Surface should be dry, clean and free of waxes, sealers, or finishes. Do not apply directly over silicone sealers, oil or wax based finishes. Aqua Mix® Sealer & Coating Remover will strip the surface and remove wax or old acrylic finishes. Place a few drops of water on various tiles. If water doesn’t penetrate, additional removal is necessary. New installations need to dry at least 48 hours before application. Clay and Saltillo tile may require extended drying time depending on temperature and humidity. Make sure the tiles are completely dry before application. Test product in obscure area to ensure desirable results.

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN.
Wear skin and eye protection. Do not breathe vapor or spray. Contains potassium methylsiliconate. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If respiratory tract is irritated, move to fresh air. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting and seek medical attention.

Limitations to the Product

Do not allow product to come in contact with any non-recommended surface.
Not recommended for use on glazed ceramic tile.
Not recommended for use around pools, showers or areas subject to standing water.
Keep surface clean and dry to reduce possibility of slip-fall accidents.

Application of Product

Read entire label before using. For new installations, sealer can be applied to a dry surface as soon as 48 hours after grouting. Surface must be clean, dry, and free of existing sealers or coatings. Apply 2-3 coats of finish with a clean dense sponge, brush or paint pad applicator in thin, even coats. Allow 30 minutes drying time between
coats.

Pre-Grouting Application

Apply over clean stone or tile a minimum of 2 hours prior to grouting – follow application procedures above.
For a highsheen finish on interior surfaces only, apply Aqua Mix® Floor Shine & Hardener over Seal & Finish Low Sheen. Allow a minimum of 2 hours drying time before applying Aqua Mix® finishes.

Drying Time

Ready for surface traffic 6 hours after final coat. Keep area dry for at least 12 hours. Achieves a full cure in 24 hours.

Cleaning of equipment

Clean tools and hands with soap and water immediately after use.

Storage

• Close container tightly after each use
• Store in original container only
• Store and use between temperatures of 40°F 90° F (4°C 32°C)
• Dispose of residue or any unused leftover product in accordance with applicable federal, state, and local requirements

Product Maintenance

Use an appropriate TileLab® or Aqua Mix® neutral cleaner for routine cleaning.

Expected Wear

EXPECTED WEAR UP TO 3 YEARS

• Will vary depending on hardness and texture of surface, type of area, surface wear, frequency, and type of maintenance products used
• Expect more frequent application on exterior areas
• Weather conditions, harsh cleaning methods, and high-alkaline, acidic, or solvent-based cleaners will affect wear

A premium, no-sheen, enhanced-look, 100% polymer-solid, penetrating sealer formulated to darken, enrich, and highlight the character and beauty of unsealed natural stone. May also be used as a pre-grouting sealer. Allows moisture vapor transmission. It also effectively seals and darkens the color of grout joints.

General Surface Prep

Surface should be dry, clean and free of waxes, sealers, or finishes.
Do not apply directly over silicone sealers, oil or wax based finishes. TileLab® HeavyDuty Stripper & Cleaner will clean the surface and remove wax or old acrylic finishes. Place a few drops of water on various tiles. If water doesn’t penetrate, additional removal is necessary. Gloss Sealer & Finish can be applied over any TileLab® sealer except Stone Sealer & Enhancer. New installations need to be cured at least 48 hours before application.
Clay and Saltillo tile may require extended drying time depending on temperature and humidity. Make sure the tiles are completely dry before application. Test product in obscure area to ensure desirable results.

Health Precautions

FLAMMABLE. MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN. Keep away from heat and sources of ignition. Wear skin and eye protection. Do not breathe vapor or spray. Contains alkyl alkoxy silane. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting, seek medical attention.

Limitations to the Product

• Do not allow sealer to come in contact with any non-recommended surface as product is not completely removable Sealers and finishes should not be used before or after use of Enrich’N’Seal™
• If Enrich’N’Seal™ is not wiped completely dry within 5 minutes, a residue may form. If residue occurs, use a scrub brush or floor machine with Aqua Mix® NanoScrub® or HeavyDuty Tile & Grout Cleaner to remove sealer residue. Always try a small test area to ensure results. If results are not satisfactory, contact Technical Services for additional options
• Keep floor surfaces dry and clean to reduce possibility of slip-fall accidents. Routine pressure-washing will affect expected wear
• Sealers will not prevent surface wear or etching from acids or caustic Chemicals

Application of Product

Read entire label before using. For new installations, sealer can be applied to a dry surface as soon as 72 hours after grouting. Surface must be clean, dry, and free of existing sealers or oatings. Apply using a sponge, brush, paint pad, cotton towel, or sprayer. NOTE: Avoid overlapping and rundown. On vertical surfaces, apply bottom to top or apply to each tile prior to installation. Be sure any sealer that does not penetrate surface is polished dry off surface within 5 minutes of each application using absorbent paper or cotton towels. If sealer residue is not completely removed from stone and grout surface within 5 minutes of application, a residue may form. If 2 or more coats are applied, allow a minimum of 30 minutes drying time between applications. Some highly porous surfaces may require an additional application after full cure insuring that all residue is removed within 5 minutes. Clean applicator tools with mineral spirits after each use.

Pre-Grouting Application

Apply over clean stone or tile a minimum of 16 hours prior to grouting – follow application procedures above.

Drying Time

Ready for surface traffic in 12 hours after final application. Keep dry for 12 hours. Achieves full cure in 48 hours.

Cleaning of equipment

Clean tools and hands with soap and water immediately after use.

Product Maintenance
Use an appropriate TileLab® or Aqua Mix® neutral cleaner for routine cleaning.

Expected Wear

EXPECTED WEAR UP TO 15 YEARS
Will vary depending on hardness and texture of surface, type of area, surface wear, frequency, and type of maintenance products used
Exterior applications may require more frequent reapplications
Weather conditions, harsh cleaning methods, and high-alkaline, acidic, or solvent-based cleaners will affect wear

Environmental Consideration

Complies with all Federal EPA and SCAQMD standards for VOC Suitable Tile Types
As a sealer or grout release for all natural stone surfaces, unglazed tile, porcelain, clay pavers, Concrete, brick, masonry, and grout. For interior and exterior use.

General Surface Prep

Surface should be dry, clean and free of waxes, sealers or finishes. New installations need to dry 48 hours before application. Protect painted surfaces. Test product in obscure area to ensure desirable results.

Health Precautions

FLAMMABLE. MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN. Keep away from heat and sources of ignition. Wear skin and eye protection. Do not breathe vapor or spray. Contains petroleum distillates, methyl alcohol, dibutyltin dilaurate, and 3- aminopropyltriethoxysilane. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If respiratory tract is irritated, remove to fresh air. If irritation persists, Seek medical attention. If swallowed, DO NOT induce vomiting. Seek medical attention.

Limitations to the Product

• Do not allow sealer to come in contact with any non-recommended
• Surface May slightly lighten or darken some stone surfaces
• Sealer will not prevent surface wear or etching from acids or caustic Chemicals

Pre-Grout Sealer/Grout Release

Porous tile, such as clay and Saltillo pavers, can be stained by grout during installation. Sealing the tile before grouting will make grout removal much easier. Apply two coats of sealer according to directions after tile has been bonded for a minimum of 24 hours, or apply to front face of tile before installation.

Application of Product

USE CHEMICAL RESISTANT GLOVES , such as nitrile, when handling product
Read entire label before using. Apply liberally using a new mop, paint pad applicator, sponge or brush. Allow it to penetrate for up to 5 minutes. Wipe surface completely dry using clean, dry cotton or paper towels after each application. Porous surfaces may require additional applications. Conduct a test to see if surface is completely sealed after 2 hours by applying drops of water on the surface. If it penetrates, apply an additional coat. If a residue is visible on the surface after drying, remove it with water and a white nylon scrub pad 60 minutes after application.

Drying Time

• Allow 30 minutes drying time between coats.
• Ready for surface traffic in 2 hours.
• Keep dry for 12 hours.
• Achieves a full cure in 24 hours.

Cleaning of equipment

Clean tools and hands with soap and water immediately after use.

Handling & Storage

• Close container tightly after each use.
• Store in original container only.
• Store and use between temperatures of 40° F 90°F (4° C 32°C).
• Dispose of residue or any unused leftover product in accordance with applicable federal, state, and local requirements.

Product Maintenance

Do not use cleaners containing ammonia, acids or bleach. Use an appropriate TileLab® or Aqua Mix® neutral cleaner. Tile industry experts recommend periodic testing of sealed surfaces. Apply a few drops of water on the surface. If it soaks in, a coat of TileLab® or Aqua Mix® sealer will be necessary to keep sealer at peak performance.

Product Maintenance

Do not use cleaners containing ammonia, acids or bleach. Use an appropriate TileLab® or Aqua Mix® neutral cleaner. Tile industry experts recommend periodic testing of sealed surfaces. Apply a few drops of water on the surface. If it soaks in, a coat of TileLab® or Aqua Mix® sealer will be necessary to keep sealer at peak performance.

Expected Wear

EXPECTED WEAR UP TO 15 YEARS
Will vary depending on hardness and texture of surface, type of area, surface wear, frequency, and type of maintenance products used Weather conditions, harsh cleaning methods, and high-alkaline, acidic, or solvent-based cleaners will affect wear

Suitable Tile Types

As a sealer or grout release for all natural stone surfaces, unglazed tile, porcelain, clay pavers, concrete, brick, masonry, and grout. For interior and exterior use.

General Surface Prep

Surface should be dry, clean and free of waxes, sealers or finishes. New installations need to dry 48 hours before application. Protect painted surfaces. Test product in obscure area to ensure desirable results.

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN.
Wear skin and eye protection. Contains glycol ether monobutyl ether. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting. Seek medical attention.

Limitations to the Product

Do not allow sealer to dry on tile surface because a residue will be visible. If this occurs, use Aqua Mix® NanoScrub® and scrub with a nylon pad
Do not allow sealer to come in contact with any non-recommended surface
Sealers will not prevent surface wear or etching from acids or caustic Chemicals

Application of Product

Read entire label before using. Apply using a soft-bristle paintbrush or sponge paint applicator. NOTE: Be sure to wipe surface completely dry within 5 minutes of each application using absorbent paper or cotton towels. After 2 hours conduct a test to determine if surface is completely sealed by applying water droplets to the surface. If water is absorbed, apply an additional coat. Wait 2 hours and repeat the test. May be reapplied as needed to grout joints that are clean.

Drying Time

Allow 30 minutes drying time between coats.
Ready for surface traffic in 2 hours.
Keep dry for 12 hours.
Achieves a full cure in 24 hours.

Cleaning of equipment

Clean tools and hands with soap and water immediately after use.

Product Maintenance

Do not use cleaners containing ammonia, acids or bleach. Use an appropriate TileLab® or Aqua Mix® neutral cleaner. Tile industry experts recommend periodic testing of sealed surfaces. Apply a few drops of water on the surface. If it soaks in, a coat of TileLab® or Aqua Mix® sealer will be necessary to keep sealer at peak performance. 9 Technical Services Information For technical assistance, contact Custom® Building Products. 10 Filing System Additional product information is available from the manufacturer upon request.

Expected Wear

EXPECTED WEAR UP TO 15 YEARS
Will vary depending on hardness and texture of surface, type of area, surface wear, frequency, and type of maintenance products used Weather conditions, harsh cleaning methods, and high-alkaline, acidic, or solvent-based cleaners will affect wear

Handling & Storage

Close container tightly after each use
Store in original container only
Store and use between temperatures of 50° F 80°F (10° C 27°C)

General Surface Prep

Surface should be dry, clean and free of any existing coatings. Do not apply directly over silicone sealers, oil or wax based finishes. Aqua Mix® Sealer & Coating Remover will strip the surface and remove wax
or old acrylic finishes. Floor Shine & Hardener can be applied over any Aqua Mix® sealer except Stone & Enhancer and Enrich N Seal. Test product in obscure area to ensure desirable results.

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN.
Wear skin and eye protection. Contains dipropylene glycol monomethyl ether. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting and seek medical attention

Limitations to the Product

Do not allow product to come in contact with any non-recommended surface.
Do not use a large-pored sponge applicator.
Do not dip applicator directly into product, as bubbling (or foaming) will occur.
Not recommended for exterior applications or for use as a finishing product on glazed ceramic or glazed porcelain tile.
Do not use around pools, showers, countertops or areas subject to standing water.
Keep surface clean and dry to reduce possibility of slip-fall accidents

Application of Product

Read entire label before using. If an Aqua Mix® sealer is used, allow sealer to cure a minimum of 24 hours unless otherwise indicated on sealer label. Unglazed surfaces must be sealed prior to using Aqua
Mix® Floor Shine & Hardener. Surface must be clean, dry and sealed. Apply by pouring a small amount of product directly onto a sealed floor and spreading evenly with a sponge mop or paint pad applicator. Avoid overlapping and puddling. Two to three coats are recommended for a high shine. If 2 or more coats are applied, allow a minimum of 1 hour drying time between coats. Clean applicator tools with soap and water after each use. May be reapplied as needed to surface that is clean and dry.

For Pre-Grouting Application

Apply over clean unglazed porcelain tile or crackled finish tile a minimum of 2 hours prior to grouting. Follow application procedures above. After grout clean-up, any remaining residue of Floor Shine &
Hardener can be removed using Aqua Mix® Heavy Duty Tile & Grout Cleaner following product directions. Unglazed surfaces must be sealed prior to using Aqua Mix® Floor Shine & Hardener.

Drying Time

Ready for surface traffic 3 hours after final coat. Keep area dry for 12 hours. Achieves a full cure in 24 hours.

Cleaning of equipment

Clean tools and hands with soap and water immediately after use.

Storage

Close container tightly after each use
Store in original container only
Store and use between temperatures of 40°F 90°F (4°C 32°C)
Dispose of residue or any unused leftover product in accordance with applicable federal, state, and local requirements

Product Maintenance

Use an appropriate TileLab® or Aqua Mix® neutral cleaner for routine cleaning.

Expected Wear

EXPECTED WEAR UP TO 1 YEAR
Will vary depending on hardness and texture of surface, type of area, surface wear, frequency, and type of maintenance products used Weather conditions, harsh cleaning methods, and high-alkaline, acidic, or solvent-based cleaners will affect wear

General Surface Prep

Surface should be dry, clean and free of waxes, sealers, or finishes.Do not apply directly over silicone sealers, oil or wax based finishes. Aqua Mix® Sealer & Coating Remover will strip the surface and remove wax or old acrylic finishes. Place a few drops of water on various tiles. If water doesn’t penetrate, additional removal is necessary. New installations need to dry at least 48 hours before application. Clay and Saltillo tile may require extended drying time depending on temperature and humidity. Make sure the tiles are completely dry before application. Test product in obscure area to ensure desirable results.

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN. Wear skin and eye protection. Do not breathe vapor or spray. Contains potassium methylsiliconate. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If respiratory tract is irritated, move to fresh air. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting and seek medical attention.

Limitations to the Product

• Do not allow product to come in contact with any non-recommended surface.
• Not recommended for use on glazed ceramic tile.
• Not recommended for use around pools, showers or areas subject to standing water.
• Keep surface clean and dry to reduce possibility of slip-fall accidents.

Application of Product

Read entire label before using. For new installations, sealer can be applied to a dry surface as soon as 48 hours after grouting. Surface must be clean, dry, and free of existing sealers or coatings. Apply 2-3 coats of finish with a clean dense sponge, brush or paint pad applicator in thin, even coats. Allow 30 minutes drying time between
coats.

Pre-Grouting Application

Apply over clean stone or tile a minimum of 2 hours prior to grouting – follow application procedures above. For a highsheen finish on interior surfaces only, apply Aqua Mix® Floor Shine & Hardener over Seal & Finish Low Sheen. Allow a minimum of 2 hours drying time before applying Aqua Mix® finishes.

Drying Time

Ready for surface traffic 6 hours after final coat. Keep area dry for at least 12 hours. Achieves a full cure in 24 hours.

Cleaning of equipment

Clean tools and hands with soap and water immediately after use.

Storage

• Close container tightly after each use
• Store in original container only
• Store and use between temperatures of 40°F 90°F (4°C 32°C)
• Dispose of residue or any unused leftover product in accordance with applicable federal, state, and local requirements

Product Maintenance

Use an appropriate TileLab® or Aqua Mix® neutral cleaner for routine cleaning.

Expected Wear

EXPECTED WEAR UP TO 3 YEARS
Will vary depending on hardness and texture of surface, type of area, surface wear, frequency, and type of maintenance products used Expect more frequent application on exterior areas Weather conditions, harsh cleaning methods, and high-alkaline, acidic, or solvent-based cleaners will affect wear

General Surface Prep

USE CHEMICAL-RESISTANT GLOVES, such as nitrile, when handling product.
Surface should be dry, clean and free of waxes, sealers or finishes. New installations need to be dry 48 hours before application. Protect surrounding surfaces. Test product in an inconspicuous area to ensure desirable results.

Health Precautions

FLAMMABLE. MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN. Keep away from heat and sources of ignition. Wear skin and eye protection. Do not breathe vapor or spray. Contains alkyl alkoxy silane. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting, seek medical attention.

Limitations to the Product

• Do not allow sealer to come in contact with any non-recommended surface as product is not completely removable
• Sealers and finishes should not be used with Enrich ‘N’ Seal™
• If Enrich’N’Seal™ is not wiped completely dry within 5 minutes, a residue may form. If residue occurs, contact Technical Services for additional options
• Keep floor surfaces dry and clean to reduce possibility of slip-fall accidents. Routine pressure-washing will affect expected wear
• Sealers will not prevent surface wear or etching from acids or caustic chemicals

Application of Product

Read entire label before using. For new installations, Enrich ‘N’ Seal can be applied to a dry surface as soon as 48 hours after grouting. Surface must be clean, dry, and free of existing sealers or coatings. Apply using a sponge, brush, paint pad, cotton towel, or sprayer. NOTE: Avoid overlapping and rundown. On vertical surfaces, apply bottom to top or apply to each tile prior to installation. Be sure any sealer that does not penetrate surface is wiped completely dry off surface within 5 minutes of each application using clean, dry, absorbent paper, cotton or microfiber towels. If sealer residue is not completely removed from stone and grout surface within 5 minutes of application, a residue may form. If 2 or more applications are used, allow a minimum of 30 minutes drying time between applications. Some highly porous surfaces may require an additional application after full cure insuring that all residue is removed within 5 minutes.

Pre-Grouting Application

Apply over clean stone or tile a minimum of 2 hours prior to grouting – follow application procedures above.

Drying Time

Ready for surface traffic 2 hours after final application. Keep dry for 12 hours. Achieves full cure in 48 hours.

Cleaning of equipment

Clean tools with mineral spirits immediately after use.

Storage

• Close container tightly after each use
• Store in original container only
• Store and use between temperatures of 45°F to 85°F (7°C to 29°C)

Product Maintenance

Do not use cleaners containing ammonia, acids or bleach. Use an appropriate TileLab® or Aqua Mix® neutral cleaner. Tile industry experts recommend periodic testing of sealed surfaces. Apply a few drops of water on the surface. If it soaks in, an additional application will be necessary to maintain peak performance.

Product Maintenance

• Will vary depending on hardness and texture of surface, type of area, surface wear, frequency, and type of maintenance products used
• Exterior applications may require more frequent reapplications
• Weather conditions, harsh cleaning methods, and high-alkaline, acidic, or solvent-based cleaners will affect wear

A concentrated, high-alkaline cleaner and degreaser. Aqua Mix® Heavy-Duty Tile & Grout Cleaner effectively removes grease, soap scum and other organic materials from areas that have been neglected or subjected to heavy use. It also removes synthetic and acrylic waxes and floor finishes.

Key Features:

• For heavily soiled and neglected areas
• Cleans ground-in dirt, grease, soap scum, and other organic materials
• Strips wax and floor finishes

Suitable Tile Types:

Natural stone (such as granite, limestone, slate and travertine), ceramic, porcelain, quarry, Saltillo, terra-cotta, cement pavers, masonry surfaces, linoleum or resilient flooring.

Health Precautions:

CORROSIVE. CAUSES BURNS. HARMFUL IF SWALLOWED. Wear skin and eye protection. Do not breathe vapor or spray. Contains sodium hydroxide and ethylene glycol monobutyl ether. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If respiratory tract is irritated, remove to fresh air. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting. Seek medical attention.

Limitations to the Product:

• Do not allow cleaner to come in contact with any non-recommended surface
• May adversely affect grout joints that have been coated with colorant or grout stain
• Regular use of high-alkaline cleaners will reduce sealer life

Application of Product:

USE CHEMICAL-RESISTANT GLOVES, such as nitrile, when handling product.

Read entire label before using. Put on rubber gloves and eye protection. Sweep, vacuum, or wipe surface. Mix Heavy-Duty Tile & Grout Cleaner as follows:

LIGHT SOIL BUILDUP: Mix 1 part cleaner to 5 parts water.
MODERATE SOIL BUILDUP: Mix 1 part cleaner to 3 parts water.
STRIPPING OR HEAVY SOIL BUILDUP: Mix 1 part cleaner to 2 parts water.
Apply solution to surface with mop or sponge. Allow to dwell 3 to 5 minutes for cleaning, or 5 to 10 minutes when stripping waxes or finishes. Agitate with synthetic mop, scrub brush, or scrub machine. Do not allow solution to dry on surface. Mop up dirty solution. Rinse thoroughly with clean water.

Cleaning of equipment:

Clean tools with water before material dries.

Storage:

• Close container tightly after each use
• Store in original container only
• Store in and use in temperatures between 45° F to 85° F (7° C to 29° C)
• Store in areas inaccessible to small children
• Do not reuse empty container, wrap and discard in trash or recycle

Product Maintenance:

Properly applied product requires no special maintenance.

Suitable Tile Types

All natural stone (such as granite, limestone, slate, and travertine),ceramic, porcelain, grout, quarry, Saltillo,terra-cotta, cement pavers,masonry surfaces, linoleum, or resilient flooring.

Limitations to the Product

Do not allow sealer to come in contact with any non-recommendedsurface
Regular use of high alkaline cleaners will reduce sealer life

Health Precautions

CORROSIVE. CAUSES BURNS. HARMFUL IF SWALLOWED. Wear skinand eye protection. Do not breathe vapor or spray. Contains sodiumhydroxide. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If respiratory tract is irritated, remove to fresh air. If irritation persists, seek medical attention. If swallowed,
DO NOT induce vomiting. Seek medical attention.

Application of Product

Read entire label before using. Sweep, vacuum, or dust surface. Mix
Stone Deep Clean as follows:
LIGHT SOIL BUILDUP: Mix 1 part cleaner to 4 parts water.
MODERATE SOIL BUILDUP: Mix 1 part cleaner to 3 parts water.
STRIPPING: Mix 1 part cleaner to 1 part water.
HEAVY SOIL BUILDUP: Use full strength.
Apply solution to surface with mop, sponge, or brush. Allow product to dwell 3 to 5 minutes for cleaning, or 5 to 10 minutes when stripping waxes or finishes. Agitate with synthetic mop, scrub brush, or scrub machine. Do not allow solution to dry on surface. Mop up dirty solution. Rinse thoroughly with clean water.

Cleaning of equipment

Clean tools and hands with water before material dries.

Storage

Close container tightly after each use
Store in original container only
Store in and use in temperatures between 40°F 90°F (4°C and 32°C)
Store in areas inaccessible to small children
Do not reuse empty container, wrap and discard in trash or recycle

Product Maintenance

Properly installed product requires no special maintenance

Suitable Tile Types

Natural stone (such as granite, limestone, marble, slate, and travertine), ceramic, porcelain, grout, quarry, Saltillo, terra-cotta, cement pavers, masonry surfaces, and other water-safe surfaces.

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN.
Wear skin and eye protection. Contains sodium (C14-16) olefin sulfonate and other surfactants. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists,
seek medical attention. If swallowed, DO NOT induce vomiting. Seek medical attention.

Application of Product

USE CHEMICAL-RESISTANT GLOVES, such as nitrile, when
handling product.
Read entire label before using. Sweep, vacuum, or dust surface. Mix 1 to 4 oz (30 to 118 mL) of Concentrated Stone & Tile Cleaner per gallon (3.8 L), of water. For polished natural stone surfaces, 1 oz (30 mL) of
Concentrated Stone & Tile Cleaner per gallon (3.8 L), of water is usually sufficient. Apply solution to surface with mop or sponge. Allow
to dwell 1 to 2 minutes. Agitate with a natural-bristle brush or white nylon scrub pad. Do not allow solution to dry on surface. Mop up dirty solution. Change cleaning solution at least every 250 ft (25 M), or as
needed.

Cleaning of equipment

Clean tools with water before material dries.

Storage

Close container tightly after each use
Store in original container only
Store in and use in temperatures between 45° F to 85° F (7° C to 29°C)
Store in areas inaccessible to small children
Do not reuse empty container, wrap and discard in trash or recycle

Product Maintenance

Properly applied product requires no special maintenance.

An effective, highly-concentrated, high-alkaline, two part (1 part powder, 1 part liquid) industrial strength cleaner and degreaser. Removes ground-in dirt, grease and soap scum. Cost effective product for use in large commercial areas such as restaurants, malls, and hotels. Also effective for quick and easy removal of all types of waxes and synthetic floor finishes.

Key Features:

• Highly concentrated cost effective
• For heavily soiled and neglected areas
• Removes ground-in dirt, grease, wax and floor finishescos

Environmental Consideration

Complies with all Federal EPA and SCAQMD standards for VOC.

Suitable Tile Types

Natural stone (such as granite, limestone, marble, slate, and travertine), ceramic, porcelain, grout, concrete, quarry, masonry surfaces and other stone and tile.

Health Precautions

CORROSIVE. CAUSES BURNS. HARMFUL IF SWALLOWED. Wear skin and eye protection. Do not breathe vapor or spray. Contains silicic acid. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If respiratory tract is irritated, move to fresh air. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting. Seek medical attention.

Limitations to the Product:

• Do not allow product to come in contact with any non-recommended surface
• Not recommended for use on vinyl or linoleum surfaces
• Do not mix with other cleaners or strippers

Mixing Procedures

• Mix powder and liquid in plastic container only
• Do not use metal or aluminum containers
• Once mixed, cleaner will remain in solution for several months
• Store unused, mixed solution in a well marked, tightly capped plastic container

Application of Product:

USE CHEMICAL-RESISTANT GLOVES, such as nitrile, when handling product.

Read entire label before using. Sweep, vacuum or wipe surface to remove loose debris. Mix 1 & 2 Deep Clean as follows in a plastic container or bucket:

CLEANING AND STRIPPING: Mix 1/4 cup (30 g) powder to 2 1/2 gallons (9.5 L) of water and mix well. Then add 1/4 cup (59 mL) of liquid and mix thoroughly.
HEAVY-DUTY CLEANING AND STRIPPING: Mix 1/2 cup (60 g) of powder to 2 1/2 gallons (9.5 L) of water and mix well. Then add 1/2 cup (118 mL) of liquid and mix thoroughly.
Note: Mixing solution with hot water is preferable, however, cold water may be used. Liberally apply cleaning solution with mop or sponge. Allow to dwell for 15 to 20 minutes. Agitate with a scrub brush or scrub machine. Do not allow solution to dry on surface. Apply additional solution if necessary. Mop up dirty solution or remove with a wet/dry vacuum. Rinse with clean water.

Cleaning of equipment:

Clean tools with water before material dries.

Storage:

• Close container tightly after each use
• Store in original container only
• Store in and use in temperatures between 45° F to 85° F (7° C to 29° C)
• Store in areas inaccessible to small children
• Do not reuse empty container, wrap and discard in trash or recycle

Product Maintenance:

Properly applied product requires no special maintenance.

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN. Wear skin and eye protection. Contains urea monohydrochloride. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting, seek medical attention

Limitations to the Product

Do not allow product to come in contact with any non-recommended surface
Do not mix with other cleaners
Acids of all kinds may etch, lighten, or change the color of cementitious material, metallic glazes and some natural stones such as marble and limestone

Application of Product

Read entire label before using. Concrete and grout installations should be cured a minimum of 10 days and be clean. Sweep, vacuum, or wipe surface. Pre-wet surface with water. Mix Phosphoric Acid Cleaner
as follows:
LIGHT SOIL BUILDUP: Mix 1 part cleaner to 5 parts water.
MODERATE SOIL BUILDUP: Mix 1 part cleaner to 3 parts water.
HEAVY SOIL BUILDUP: Mix 1 part cleaner to 2 parts water.
Apply solution to wet surface and scrub with a nylon bristle brush. Work in small areas. Flush with water immediately after brushing. Do not use repeatedly or surface damage may occur. For heavy concrete
etching, allow solution to sit for up to 30 minutes prior to flushing with clean water. For lighter grout haze, Phosphoric Acid Substitute may be diluted up to 3:1.

Cleaning of equipment

Clean tools and hands with water before material dries.

Product Maintenance

Properly installed product requires no special maintenance.

Handling & Storage

Close container tightly after each use
Store in original container only
Store in and use in temperatures between 40° F 90°F (4° C 32°C)
Store in areas inaccessible to small children
Do not reuse empty container, wrap and discard in trash or recycle

Health Precautions

CORROSIVE. CAUSES BURNS. HARMFUL IF SWALLOWED. Wear skin and eye protection. Do not breathe dust. Contains sulfamic acid. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If respiratory tract is irritated, move to fresh air. If irritation persists, seek medical attention. If swallowed, DO NOT induce
vomiting, seek medical attention. KEEP OUT OF REACH OF CHILDREN

Limitations to the Product

Do not allow product to come in contact with any non-recommended surface
Do not mix with ammoniated cleaners, such as bleach, as harmful fumes will result
Not recommended for highly porous tile such as Saltillo
Acids of all kinds may etch, lighten or change the color of cementitious material, metallic glazes and stones containing calcium, such as marble and other acid sensitive stone

Application of Product

Read entire label before using. Allow newly grouted installation to cure a minimum of 10 days. Sweep, vacuum, or wipe surface. Mix Sulfamic Acid Crystals as follows: LIGHT TO NORMAL CLEANING: Mix 1/2 cup (150 g) of Crystals to 1
gallon of water. Mix Crystals until dissolved. HEAVY-DUTY CLEANING: Mix 3/4 cup (225 g) of Crystals to 1 gallon of
water. Mix Crystals until dissolved. Pre-wet surface with water. Apply solution with mop or sponge. Allow to dwell 1 to 2 minutes. Agitate with white nylon scrub pad or scrub brush. Do not allow solution to dry on surface. Rinse thoroughly with clean water, agitating with white nylon scrub pad or brush to ensure removal of acid. Rinse again in the same manner to be sure acid is removed.

Cleaning of equipment

Clean tools and hands with water before material dries.

Handling & Storage

Close container tightly after each use
Store in original container only
Store in and use in temperatures between 40° F 90°F (4° C 32°C)
Store in areas inaccessible to small children
Do not reuse empty container, wrap and discard in trash or recycle

Product Maintenance

Properly installed product requires no special maintenance

General Surface Prep

Test a small area according to application instructions to determine desired results.

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN.
Wear skin and eye protection. Contains glycol ether PNB, oxalic acid, and glycolic acid. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting, seek medical attention. KEEP OUT OF REACH OF CHILDREN

Limitations to the Product

Do not use on polished, acid-sensitive stone (such as marble and limestone)
Do not allow product to come in contact with any non-recommended surface
Do not mix with ammoniated cleaners, such as bleach, as harmful fumes will result
Acids of all kinds may etch, lighten, or change the color of cementitious
material, metallic glazes and some natural stones such as marble and limestone

Application of Product

Read entire label before using. Remove loose debris. Pre-wet the
surface with water and remove excess before applying solution. Mix
ExTreme® as follows:
LIGHT BUILDUP: Mix 1 part cleaner to 4 parts water.
MODERATE BUILDUP: Mix 1 part cleaner to 2 parts water.
HEAVY BUILDUP: Use undiluted.
Liberally apply solution with paint roller, brush or sponge. Allow to dwell up to 30 minutes. DO NOT ALLOW SOLUTION TO DRY ON SURFACE. Apply additional solution if drying occurs. Agitate with scrub brush thoroughly rinse with clean water. For vertical surfaces a garden hose or high-pressure washer may be used to rinse area. Mop or wet vacuum dirty solution. Heavy buildup may require additional applications and a longer dwell time.

Cleaning of equipment

Clean tools and hands with water before material dries.

Product Maintenance

Properly installed product requires no special maintenance.

Handling & Storage

Close container tightly after each use Store in original container only
Store in and use in temperatures between 40° F 90°F (4° C 32°C)
Store in areas inaccessible to small children
Do not reuse empty container, wrap and discard in trash or recycle

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN.
Wear skin and eye protection. Contains barium sulfate and silicic acid. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting, seek medical attention

Limitations to the Product

Do not allow product to come in contact with any non-recommended surface Extreme care should be taken with dark marble (especially green), as it may be more sensitive to moisture
Light abrasive action or high RPMs on the surface of some marbles may dull the high-polished finish

Application of Product

FOR REMOVING DEEP-SET OIL AND GREASE STAINS: Read entire label before using. Mix Poultice Stain Remover powder
with water to form a thick, pliable paste. Quantity of Poultice Stain Remover needed will depend on size of stain. Apply a 1/4″ (6 mm) thick layer of paste directly over stain with at least a 1″ (25 mm) overlap beyond edge of stain. Cover with plastic or wax paper. Poke a few very small holes in plastic cover to allow for minimum air
exposure. Allow paste to stand on stain for 24 to 48 hours. Remove Poultice Stain Remover with plastic spatula or plastic putty knife and wash off residue with clean water. Repeat procedure if necessary. If area darkens from absorbed moisture, it should dry completely within 2 to 4 days. FOR REMOVING STUBBORN SURFACE STAINS AND GROUT RESIDUE ON ACID SENSITIVE STONE:
Read entire label before using. Protect surrounding areas from splattering to minimize cleanup. Pre-wet a manageable area of the surface with water, approximately 10 ft (1 M) and sprinkle Poultice Stain Remover onto the area mixing into a thin slurry. If surface is vertical, mix slurry in a container and apply to pre-wet surface. Agitate by hand or with low RPM (300-750 RPM) buffer using a white nylon scrub pad. Keep surface wet throughout buffing process. Remove Poultice Stain Remover solution with clean towels or sponge and rinse twice with clean water. A wet/dry vacuum may be used. Polish surface dry with clean, dry towels or buff with soft lambs wool pad. Rinse with clean water and buff dry with clean towels
NOTE: Poultice Stain Remover is an excellent additive that will boost the cleaning power of many of the Aqua Mix® cleaners such as Phosphoric Acid Substitute, Heavy-Duty Tile & Grout Cleaner, and
Stone Deep Clean.

Cleaning of equipment

Clean tools and hands with water before material dries.

Handling & Storage

Close container tightly after each use
Store in original container only
Store in and use in temperatures between 40° F 90°F (4° C 32°C)
Store in areas inaccessible to small children
Do not reuse empty container, wrap and discard in trash or recycle

Product Maintenance

Properly installed product requires no special maintenance.

General Surface Prep

Test a small area according to application instructions to determine desired results.

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN.
Wear skin and eye protection. Contains trisodium citrate dihydrate, sodium tripolyphosphate, and Beta-Alanine, N -(2-carboxyethyl)-N-(2- ethylhexyl)-monosodium salt. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting, seek medical attention. KEEP OUT OF REACH OF CHILDREN.

Limitations to the Product

Do not allow product to come in contact with any non-recommended surface
Not recommended for use on polished marble, limestone, and travertine surfaces
If efflorescence appears after surface is sealed, EffEx ® will remove the efflorescence but its ability to inhibit efflorescence is reduced

Application of Product

To Remove Efflorescence:
Read entire label before using. Do not dilute product. For best results it is recommended to pre-wet the surface with water, avoid puddling and remove excess water before applying solution. Liberally apply solution with mop, sponge applicator, paint roller or brush. Allow to dwell 10- 15 minutes. Do not allow solution to dry on surface. Apply additional solution if drying occurs. Agitate with scrub brush or scrub machine. Thoroughly rinse with clean water. For vertical surfaces a garden hose or high-pressure washer may be used to rinse area. Mop or wet
vacuum up dirty solution. Heavily built-up efflorescence may require additional applications and a longer dwell time. Allow area to dry 24 hours prior to sealing area with any Aqua Mix® sealer. To Inhibit Efflorescence: Apply a thin coat of solution with mop, sponge applicator, paint roller or brush. Scrub into surface with scrub brush or scrub machine. DO NOT RINSE. Wipe dry any product remaining on the surface. Several treatments may be required to fully inhibit efflorescence. Allow area to dry 24 hours prior to sealing area with any Aqua Mix® sealer.
Cleaning of equipment Clean tools and hands with water before material dries.

Product Maintenance

Properly installed product requires no special maintenance.

Handling & Storage

Close container tightly after each use
Store in original container only
Store in and use in temperatures between 40° F 90°F (4° C 32°C)
Store in areas inaccessible to small children
Do not reuse empty container, wrap and discard in trash or recycle

General Surface Prep

Test a small area according to application instructions to determine desired results.

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN.
Wear skin and eye protection. Contains coconut oil, DEA and ethoxylated alcohol. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting, seek medical attention. KEEP OUT OF REACH OF CHILDREN

Limitations to the Product

Do not allow product to come in contact with any non-recommended surface.

Application of Product

Read entire label before using. SHAKE WELL BEFORE USING. Sweep, vacuum, or dust surface to remove any loose debris. Pre-wet surface with a liberal amount of water. Apply NanoScrub® directly to the wet surface. Agitate with a white nylon pad, scrub brush or scrub machine. Mop or wet vacuum up residue. Rinse thoroughly with clean water. NanoScrub® can be used as a power booster, with Aqua Mix® HeavyDuty Tile & Grout Cleaner, Stone Deep Clean, or 1&2 Deep Clean mixed according to directions. Apply chosen product to surface, add NanoScrub® and agitate mixture. Continue to follow directions on the chosen product making sure a clean water rinse is the final step to remove any remaining residue.

Cleaning of equipment

Clean tools and hands with water before material dries

Handling & Storage

Close container tightly after each use
Store in original container only
Store in and use in temperatures between 40° F 90°F (4° C 32°C)
Store in areas inaccessible to small children
Do not reuse empty container, wrap and discard in trash or recycle

Product Maintenance

Properly installed product requires no special maintenance.

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN.
Wear skin and eye protection. Contains 2-butoxyethanol, ethyl 3- ethoxypropionate, and tripropylene glycol monomethyl ether. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting, seek medical attention.

Limitations to the Product

Do not allow product to come in contact with any non-recommended surface
Do not spray
Do not use on resinous synthetic agglomerates

Application of Product

STRIPPING:
Read entire label before using. SHAKE WELL before using. Sweep or vacuum surface. Apply a liberal amount of Sealer & Coating Remover to a small, manageable area of up to 25 ft (2 M). Spread with a mop, sponge, or brush. Allow product to dwell up to 1 hour without drying or until coating or residue softens. Do not allow Sealer & Coating Remover to dry on surface – if remover starts to dry, add more to ensure surface is kept wet. Agitate with a scrub brush or scrub machine. Wipe up residue with clean, absorbent white cotton towels or sponge. A wet/dry vacuum may be used. Removal of thick coatings or residue may require several applications – repeat steps 3 through 7 if coating is still on surface. Rinse thoroughly with clean water. Ready for surface traffic in 1 hour or after fumes have dissipated. Allow at least 24hour drying time before applying Aqua Mix® sealers and floor finishes.

EPOXY GROUT HAZE REMOVAL:

Read entire label before using. SHAKE WELL before using. Apply a minimal amount of Sealer & Coating Remover (just enough to make the surface damp) to a small manageable area of up to 25 ft (2 M). Spread with a mop, sponge, or brush. Lightly agitate surface with a scrub brush until haze is removed. For large commercial installations,
a white pad may be used with a scrub machine. Mop up dirty solution. Rinse thoroughly with clean water. Ready for surface traffic in 1 hour or after fumes have dissipated. Allow at least 24-hour drying time
before applying Aqua Mix® sealers and floor finishes.

Cleaning of equipment

Clean tools and hands with water before material dries.

Product Maintenance

Properly installed product requires no special maintenance.
Handling & Storage
Close container tightly after each use
Store in original container only
Store in and use in temperatures between 40° F 90°F (4° C 32°C)
Store in areas inaccessible to small children
Do not reuse empty container, wrap and discard in trash or recycle

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN. Wear skin and eye protection. Contains EDTA acid, sodium
tripolyphosphate, trisodium citrate dihydrate, and Beta-Alanine, N -(2- carboxyethyl)-N-(2-ethylhexyl)-monosodium salt. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting, seek medical attention

Limitations to the Product

Do not allow product to come in contact with any non-recommended surface
Do not use on polished marble or any other acid-sensitive tile or stone
Do not use excessive amounts of water during cleanup process as grout pigment may be washed out

Application of Product

DURING GROUT CLEANUP:
Read entire label before using. Perform grout cleanup per grout manufacturer’s instructions. During final grout cleanup rinse, mix a minimum of 3 oz (90 mL) of Grout Haze Clean-Up per gallon (3.8 L) of water. Wet a grout sponge or terry cloth towel with the cleaning solution, wring out excess liquid. Wipe diagonally across the tile.
Repeat steps 4 and 5 every 10 to 15 ft (.9 M to 1.3 M) or as necessary. Remove residual cleaning solution using a clean grout sponge or terry cloth towel dampened with clean water only.
AFTER GROUT CLEANUP WITHIN 10 DAYS OF GROUTING:
Use full strength if grout haze was not completely removed during grout cleanup. Apply directly to surface and agitate with white nylon scrub pad or brush. Allow product to dwell for 5 to 10 minutes for stubborn areas or heavier grout residue. Rinse with clean water to remove residual cleaning solution.

Cleaning of equipment

Clean tools and hands with water before material dries

Product Maintenance

Properly installed product requires no special maintenance.

Handling & Storage

Close container tightly after each use
Store in original container only
Store in and use in temperatures between 40° F 90°F (4° C 32°C)
Store in areas inaccessible to small children
Do not reuse empty container, wrap and discard in trash or recycle

Suitable Tile Types

Calcium-based polished natural stone (such as limestone, marble, and travertine) and cement-based precast terrazzo.

Health Precautions

CORROSIVE. CAUSES BURNS. HARMFUL IF SWALLOWED. Wear skin
and eye protection. Do not breathe dust. Contains potassium oxalate. If
in eyes, flush with water for at least 15 minutes. If on skin, wash with
soap and water. If respiratory tract is irritated, move to fresh air. If
irritation persists, seek medical attention. If swallowed, DO NOT induce
vomiting, seek medical attention.

Limitations to the Product

Do not allow product to come in contact with any non-recommended surface
May not be suitable for some green marbles
Severely damaged or worn polished marble may require professional resurfacing
Not intended for use on granite, porcelain, ceramic tile or cultured marble
For large floor surfaces, Aqua Mix® Reviver is recommended

Application of Product

Read entire label before using. SHAKE WELL before using. Surface must be clean, dry and free of existing surface coatings. Apply a small amount (tablespoon or less) of Renue® directly onto etched or worn area. Use spray bottle to apply 1-2 squirts of water directly on Renue®. Using a soft cotton or terry towel, buff Renue® into worn or
etched area until slurry becomes clear and nearly dry. Re-wet with water and polish dry completely with absorbent towel. Repeat process if necessary until desired results are achieved. A handheld buffer with soft bonnet may be used for quicker results for larger areas. Cleaning of equipment Clean tools and hands with water before material dries

Handling & Storage

Close container tightly after each use
Store in original container only
Store in and use in temperatures between 40° F 90°F (4° C 32° C)
Store in areas inaccessible to small children
Do not reuse empty container, wrap and discard in trash or recycle

Product Maintenance

Properly installed product requires no special maintenance

Suitable Tile Types

Limestone, marble and travertine

General Surface Prep

Test a small area according to application instructions to determine desired results.

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN.
Wear skin and eye protection. Contains nonreactive mineral powders. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting, seek medical attention. KEEP OUT OF REACH OF CHILDREN.

Limitations to the Product

Do not allow product to come in contact with any non-recommendedsurface.
Not intended for use as a pre-polish powder

Application of Product

Read entire label before using. Test in a small inconspicuous area to determine desired results. Sweep or vacuum surface. Protect baseboards, carpet, etc. with protective plastic and/or blue painters tape. Surface must be free of existing sealers or coatings. Liberally apply KnockDown® to the stone surface. Add water to form a slurry.
Refinish using a weighted floor machine fitted with a natural hair or synthetic fiber tan floor pad or use a hand polishing machine. If lippage is present, use two pads, double stacked. Keep slurry wet while buffing. Add KnockDown® as needed. Harder stones will require a thicker slurry. Buff area until the desired level of hone has been achieved squeegee slurry from a small area to check for desired results prior to removing slurry. Rinse well and use a wet vacuum to remove all excess compound.

Cleaning of equipment

Clean tools and hands with water before material dries.

Handling & Storage

Close container tightly after each use
Store in original container only
Store in and use in temperatures between 40° F 90°F (4° C 32°C)
Store in areas inaccessible to small children
Do not reuse empty container, wrap and discard in trash or recycle

Product Maintenance

Properly installed product requires no special maintenance.

Suitable Tile Types

Polished limestone, marble, travertine and cement-based precast terrazzo.

General Surface Prep

Test a small area according to application instructions to determine desired results.

Health Precautions

CORROSIVE. CAUSES BURNS. HARMFUL IF SWALLOWED. Wear skin and eye protection. Do not breathe dust. Contains potassium oxalate. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If respiratory tract is irritated, move to fresh air. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting, seek medical attention. KEEP OUT OF REACH OF CHILDREN.

Limitations to the Product

Do not allow product to come in contact with any non-recommended surface
May not be suitable for some green marbles Severely damaged or worn polished marble may require professional
resurfacing Not intended for use on granite, porcelain, ceramic tile or cultured Marble

Application of Product

Read entire label before using. MIX WELL before using. Sweep or vacuum surface. Surface to be polished must be free of existing sealers or coatings. Protect baseboards, carpet, etc. with protective plastic and/or blue painters tape. Wet an area no larger than 20 ft (2M)with clean water and place 2 tablespoons of Reviver® in the center.
Using a natural hair or synthetic fiber tan floor pad, work the area in a side-to-side motion with a 175 to 300 RPM floor machine. The consistency of the slurry should be fluid enough to achieve even coverage. If the slurry becomes too dry, add water as required. For large areas, work in small sections and be sure to overlap the sections to achieve an even polish. Continue until the required polish has been achieved – squeegee slurry from a small area to check for desired results prior to removing slurry. Use a wet-dry vacuum to remove slurry and rinse thoroughly. Polish dry with a new polishing pad or cotton bonnet.
NOTE: An even higher shine can be achieved by using Marble Re-Polish.

Cleaning of equipment

Clean tools and hands with water before material dries.

Product Maintenance

Properly installed product requires no special maintenance

Handling & Storage

Close container tightly after each use
Store in original container only
Store in and use in temperatures between 40° F 90°F (4° C 32°C)
Store in areas inaccessible to small children
Do not reuse empty container, wrap and discard in trash or recycle

General Surface Prep

Test a small area according to application instructions, with a
minimum 1-hour cure time to determine desired results.

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN.
Wear skin and eye protection. Contains styrene-acrylic copolymer. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists, seek medical attention. If
swallowed, DO NOT induce vomiting, seek medical attention. KEEP OUT OF REACH OF CHILDREN

Limitations to the Product

Grout Colorant is not recommended for use underwater in pools, ponds, or on areas subject to hydrostatic pressure
Do not use solvent-based cleaners, abrasive equipment or high-pressure washing equipment on recolored grout joints.
Previously applied sealers, with the exception of Aqua Mix® Penetrating Sealer, Aqua Mix® Grout Sealer, Aqua Mix® ProSolv, Aqua Mix® UltraSolv® or Aqua Mix® Sealer’s Choice® Gold, must be removed to provide a bondable surface. Aqua Mix® Sealer & Coating Remover is recommended for this procedure
Porous tile may require sealing to ensure colorant is not absorbed into the tile

Application of Product

Read entire label before using. SHAKE WELL before using. For new installations, Grout Colorant can be applied as soon as 48 hours after grouting. Grout joints must be clean, dry and free of existing sealers or
coatings. Prepare existing grout joints: MOST TILE & STONE: Use Aqua Mix® Grout Colorant PreTreat
Cleaner or Aqua Mix® Phosphoric Acid Substitute. ACIDSENSITIVE STONE: Use Aqua Mix® HeavyDuty Tile & Grout
Cleaner EPOXY GROUT JOINTS: Use Aqua Mix® Sealer & Coating Remover.
If more than 1 bottle of a single color is to be used, mix the material together in a large container to ensure uniformity of color. If using Grout Colorant Applicator, pour Grout Colorant into Applicator bottle and apply a bead onto grout joint. Spread evenly using the Applicator Brush or toothbrush, working Grout Colorant into joint using a backand- forth motion. Thin, even coats should be applied, limiting the amount of Grout Colorant that gets on the tile. If going from a dark to light grout color, more than 1 application may be necessary with a
minimum 2-hours drying time between coats. After Grout Colorant has dried 1 or more hours (never more than 12 hours), lightly mist surface with water and let stand 5 minutes. Remove excess Grout Colorant from surface of tile using water and a white nylon scrub pad. Ready for surface traffic in 2 hours. Keep area dry for at least 24 hours. Avoid direct scrubbing on grout joints for 20 days to allow a full cure. Clean applicator tools with water after each use.

Drying Time

2 hours

Cleaning of equipment

Clean tools and hands with water before material dries.

Expected Wear

Expected Wear Up To 15 Years
Will vary depending on hardness and texture of surface, type of area,
surface wear, frequency, and type of maintenance products used.
Weather conditions, harsh cleaning methods and high-alkaline, acidic
or solvent-based cleaners will affect wear.

Handling & Storage

Close container tightly after each use
Store in original container only
Store in and use in temperatures between 40° F 90°F (4° C 32°C)
Store in areas inaccessible to small children
Do not reuse empty container, wrap and discard in trash or recycle

Suitable Tile Types

Sanded and non-sanded grout joints

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN.
Wear skin and eye protection. Contains urea monohydrochloride. If in yes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting, seek medical attention.

Limitations to the Product

Do not allow product to come in contact with any non-recommended surface
Do not mix with ammoniated cleaners, such as bleach, as harmful fumes will result
Not recommended on acid sensitive stone and metallic glazes.
Will etch, lighten, or change the color of metallic glazes and some natural stones such as marble and limestone.

Application of Product

Read entire label before using. Allow newly grouted installation to cure a minimum of 10 days. Sweep, vacuum or wipe surface to remove loose debris. Pre-wet surface with water. Spray Grout Colorant Pre- Treat Cleaner directly onto grout joints in manageable area of approximately 5 to 6 ft (0.5 M to 1 M). Allow to dwell 1 to 2 minutes.
Scrub grout joints with nylon or natural-bristle scrub brush or white nylon scrub pad. Do not allow solution to dry on surface. Mop up dirty solution. Rinse thoroughly with clean water, agitating with white nylon scrub pad or brush to ensure removal of cleaning agents and acid. Completely dry surface with clean, dry absorbent towels. Allow a
minimum of 2 hours drying time prior to applying Aqua Mix® Grout Colorant. For preparing epoxy grout joints, use Aqua Mix® Sealer & Coating Remover.

Cleaning of equipment

Clean tools and hands with water before material dries

Handling & Storage

Close container tightly after each use
Store in original container only
Store in and use in temperatures between 40° F 90°F (4° C 32°C)
Store in areas inaccessible to small children
Do not reuse empty container, wrap and discard in trash or recycle

Product Maintenance

Properly installed product requires no special maintenance

Suitable Tile Types

Saltillo and other high porosity Adobe clay tile
Effective for interior and exterior applications

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN.
Wear skin and eye protection. Contains urea monohydrochloride. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting, seek medical attention

Limitations to the Product

Previously applied sealers must be removed as Aqua Stain must penetrate into porous tile. Aqua Mix® Sealer & Coating Remover is recommended to remove existing sealers.

Application of Product

USE CHEMICAL-RESISTANT GLOVES, such as nitrile, when handling product. Read entire label before using. SHAKE WELL before using. TEST A SMALL AREA according to application instructions, with a 24-hour cure time to determine desired results. Allow new installations to cure 24 hours before applying Aqua Stain for Saltillo. Surface must be clean and free of existing sealers or coatings. Aqua Stain may be used undiluted if a darker stain is desired or diluted with up to 8 parts water for lighter, more translucent stain. Pre-dampen tiles with water. Select
a small, manageable area of 4 to 6 ft (.35 M to .55 M) and apply Aqua Stain for Saltillo with a dense sponge or lint-free cotton towel from a shallow dish. For best results, apply to individual tiles by hand. Rub
into the tile in a circular motion using as much or as little stain as needed to achieve the desired appearance from the test area. If too much stain is applied or streaking occurs, immediately rework the area with a clean, damp sponge or towel and simply rub out the area using small amounts of water. For both interior and exterior applications, use Aqua Mix® Seal & Finish Low Sheen to seal, protect the color, and provide a durable low-sheen finish. If used on an interior application, and a high-sheen finish is desired, apply Aqua Mix® Floor Shine &
Hardener over the Seal & Finish Low Sheen. Clean applicator tools with water after each use.

Cleaning of equipment

Clean tools with water and soap before material dries.

Product Maintenance

Do not use cleaners containing amonia acids or bleach; use appropriate TileLab or Aqua Mix cleaners

Handling & Storage

Close container tightly after each use
Store in original container only
Store in and use in temperatures between 45° F to 85° F (7° C to 29°C)
Store in areas inaccessible to small children
Do not reuse empty container, wrap and discard in trash or recycle